Producent oprogramowania Fortinet opublikował aktualizację dla FortiSwitch 7.0.8, która zawiera kilka poprawek błędów. Naprawiono między innymi problemy w interfejsie GUI dla topologii FortiLink z włączoną obsługą VDOM. Poprawiono zakłądkę Managed FortiSwitches, która błędnie wyświetlała ostrzeżenie o niezarejestrowanym urządzeniu Fortiswitch pomimo tego, że było zarejestrowane – sytuacja dotyczyła jednostek przeniesionych. Więcej szczegółów aktualizacji można znaleźć poniżej.
Rozwiązane problemy:
| Bug ID | Description |
|---|---|
| 777145 | The Managed FortiSwitches page incorrectly shows a warning about an unregistered FortiSwitch unit even though it is registered. This only impacts transferred or RMAed FortiSwitch units. This is only a display issue with no impact on the FortiSwitch unitʼs operation. |
| 794026 | The number of targets that can be configured in the config user quarantine command has been raised from 256 to 4,000. |
| 803307 | The Security Rating message of “Enable STP” was changed to “To avoid a switching loop, enable STP on the FortiSwitch ports once network topology is stable.” |
| 805154 | The pre-configuration for FS-108F-POE shows the wrong number of PoE ports. |
| 810550 | When synchronizing the configuration between the FortiGate device and some managed FortiSwitch units, “errno = 6” appears in the error logs. |
| 825377 | After upgrading to FortiOS 7.0.6, there are multiple problems in the GUI for a FortiLink topology with VDOMs enabled. |
| 836604 | The command for the managed switch port speed for a 40-Gbps copper interface was missing. You can now select set speed 40000cr4. |
| 838110 | The set speed 25000cr4 command was changed to set speed 25000cr, and the set speed 25000sr4 command was changed to set speed 25000sr. |
| 838880 | When you use NAC policies with EMS tags and switch groups, the endpoint does not match any policy if the endpoint matches both EMS tags and the switch groups are different. |
Znane problemy:
| Bug ID | Description |
|---|---|
| 298348, 298994 | Enabling the hw-switch-ether-filter command on the FG-92D model (the default setting) causes FortiSwitch devices to not be discovered. |
| 520954 | When a “FortiLink mode over a layer-3 network” topology has been configured, the FortiGate GUI does not always display the complete network. |
| 527695 | Starting in FortiOS 6.4.0, VLAN optimization is enabled by default (set vlan-optimization enable under config switch-controller global). On a network running FortiSwitchOS earlier than 6.0.0, this change results in a synchronization error, but the network still functions normally. If you have FortiSwitchOS 6.0.x, you can upgrade to remove the synchronization error or disable VLAN optimization.
On a network with |
| 586801 | NetBIOS stops working when proxy ARP is configured and the access VLAN is enabled because FortiGate units do not support NetBIOS proxy. |
| 621785 | user.nac-policy[].switch-scope might contain a data reference to switch-controller.managed-switch. When this reference is set by an admin, the admin needs to remove this reference before deleting the managed-switch. |
| 789914 |
|
| 813216 | After CAPWAP offload is enabled or disabled, FortiLink goes down. |
| 891642 | The FortiGate 6000 and 7000 platforms do not support managing FortiSwitch devices over FortiLink. |
| 939011 | The config switch-controller auto-config policy and config switch-controller qos commands are not supported in VDOMs with transparent mode. |
Notatki producenta: FortiSwitch 7.0.8
Pozdrawiamy,
Zespół B&B
Bezpieczeństwo w biznesie