Aktualizacja oprogramowania dla przełączników FortiSwitch wykorzystujące oprogramowanie z rodziny 6.0.X została właśnie opublikowana! W nowej wersji FortiSwitch 6.0.3 urządzenia zyskały możliwość autentykacji do 20 urządzeń per port wykorzystując autentykację 802.1x bazującą na adresach MAC.

Wprowadzone poprawki:

Bug ID Description

488263 Users should not be able to submit requests multiple times by clicking the Edit, Update, Reset, Delete, or OK, buttons in the GUI more than once.
493485 Upgrading the FortiSwitch firmware should not disable switch ports or stop daemons during the upgrade.
498265 The Uptime and System Time values on the System > Dashboard page should be accurate.
512597 The Reset button on the Switch > Port > Physical page should be changed to POE Reset.
512988 When IGMP snooping is enabled on a VLAN on some FortiSwitch units, ARP broadcast from the server does not work.
521441 The “internal” system interface does not perform hardware offloading of routes and is only software forwarding. Users can use VLAN switched virtual interfaces for full hardware offloading.
521981 The Router > Monitor > Routing page needs pagination.
522491 When the CLI console is closed in the GUI, the session should end.
522767 The maximum number of trunks needs to be changed from 48 to 128.
523275 When configuring OSPF routing using the CLI, the set authentication
command is not needed and should be removed.
523411 The diagnose switch poe status command needs to report the correct values.
523643 The GUI and CLI should report the same values for memory used.
523757 The values for the charts on the System > Dashboard page should be present and not overlapping.
529191 Going to WiFi & Switch Controller > Managed FortiSwitch sometimes shows a dotted line instead of a solid line between the FortiGate unit and the managed FortiSwitch unit.

529268 The Speed column on the Port Trunks page (Switch > Port > Trunk) should be renamed to “PSC.”
529554 When editing an LLDP-MED profile, the Edit button should be an Update button.
529785 When scp-admin is enabled and a custom profile is used, the administrator cannot download the config file using the secure copy protocol (SCP).
530517 When dynamic ARP inspection (DAI) is enabled, ping does not work consistently.

Znane problemy:

Bug ID Description
380239 IGMP-snooped multicast groups are not immediately flushed out of the snooping table when the querier port is shut down.
391607 Switch does not send gratuitous ARP for IP conflict when the system boots up and adds a new switch virtual interface (SVI).
414972 IGMP snooping might not work correctly when used with 802.1x Dynamic VLAN functionality.
416655 When using DHCP, the IPv6 address cannot be configured. Also, the automatic configuration of the global address does not work.
438441 DHCP snooping and dynamic ARP inspection (DAI) do not work with private VLANs (PVLANs).
480605 When DHCP snooping is enabled on the FSR-112D-POE, the switched virtual interface (SVI) cannot get the IP address from the DHCP server.
488044 On a Protocol Independent Multicast (PIM) topology using the assert mechanism, when the assert winner lost the route to the source, no multicast route was created, and the multicast traffic stopped.
510943
When using the cable diagnostics feature on a port (with the diagnose switch physical-ports cable-diag <physical port name> CLI command),
ensure that the physical link on its neighbor port is down. You can disable the neighbor ports or physically remove the cables.
520954 When a “FortiLink mode over a layer-3 network” topology has been configured, the FortiGate GUI does not always display the complete network.
534922 Upgrading from FortiSwitchOS 6.0.3 can cause the switch to stop responding. Workaround: Power cycle the switch.